Część zamienna do AOYUE 474 701 808 2702 końcówka do rozlutowywania 1,0 mm z długim trzonkiem

PCBs and plates can be easily and safely fixed with the Aoyue 328 Working Platform without using a "third hand" that could damage components or other circuit paths. The brass spindle of the Working Platform can be adjusted by means of knurled plastic wheel. The Working Platform has more storage possibilities for tools (see product pictures) so that the working place is tidied up and the tool is always there where it is needed. The jaws (metal plate holder) of the Working Platform are not made of plastic but of metal so that when hot air is applied no damage may occur.

- sure fixing of the chip for the reballing - sure and clean reballing with a low cost expenditure - about 50 further models available Place the stencil template that matches precisely the pitch pattern of the BGAs. Spread the solder balls on the solder pads. If all pads have received a solder ball, remove the excess balls. The solder balls can melt only on the solder pads. After the stencil template and the BGA’s have been cooled down, the stencil template ca be removed.

This product leaves the range, as we want to make room for new products. We are happy to advise you if you need an alternative for this station. The spare parts will be available in future. The platform Aoyue 618 allows you to work easily and safely on the pc board. The fixing screws sustain the pc board safely on the holder/support. The holder of the versatile working platform allows you to set the required distance between the clamped hot air gun and the pc board without problems. This way you have the possibility to establish a precise adjustment to reach an always constant soldering result. While working with the platform you need both free hands to work on the pc board or to make the settings on the hot air station. The pillar of the holder is hard chrome plated to protect the surface.

• sure fixing of the chip for the reballing • sure and clean reballing with a low cost expenditure • about 50 further models available Place the stencil template that matches precisely the pitch pattern of the BGAs. Spread the solder balls on the solder pads. If all pads have received a solder ball, remove the excess balls. The solder balls can melt only on the solder pads. After the stencil template and the BGA’s have been cooled down, the stencil template ca be removed.

- sure fixing of the chip for the reballing - sure and clean reballing with a low cost expenditure - about 50 further models available Place the stencil template that matches precisely the pitch pattern of the BGAs. Spread the solder balls on the solder pads. If all pads have received a solder ball, remove the excess balls. The solder balls can melt only on the solder pads. After the stencil template and the BGA’s have been cooled down, the stencil template ca be removed.

- sure fixing of the chip for the reballing - sure and clean reballing with a low cost expenditure - about 50 further models available Place the stencil template that matches precisely the pitch pattern of the BGAs. Spread the solder balls on the solder pads. If all pads have received a solder ball, remove the excess balls. The solder balls can melt only on the solder pads. After the stencil template and the BGA’s have been cooled down, the stencil template ca be removed.

- sure fixing of the chip for the reballing - sure and clean reballing with a low cost expenditure - about 50 further models available Place the stencil template that matches precisely the pitch pattern of the BGAs. Spread the solder balls on the solder pads. If all pads have received a solder ball, remove the excess balls. The solder balls can melt only on the solder pads. After the stencil template and the BGA’s have been cooled down, the stencil template ca be removed.

- sure fixing of the chip for the reballing - sure and clean reballing with a low cost expenditure - about 50 further models available Place the stencil template that matches precisely the pitch pattern of the BGAs. Spread the solder balls on the solder pads. If all pads have received a solder ball, remove the excess balls. The solder balls can melt only on the solder pads. After the stencil template and the BGA’s have been cooled down, the stencil template ca be removed.

- sure fixing of the chip for the reballing - sure and clean reballing with a low cost expenditure - about 50 further models available Place the stencil template that matches precisely the pitch pattern of the BGAs. Spread the solder balls on the solder pads. If all pads have received a solder ball, remove the excess balls. The solder balls can melt only on the solder pads. After the stencil template and the BGA’s have been cooled down, the stencil template ca be removed.

This model 927 distinguishes itself by colourfast light, whereby no irritations can occur. The lamp is best suitable for the deciphering of small components on the board or for soldering without additional aids.The LED lamp can be used for checking if the joints on the board have flaws, which is not possible with the normal eye. It has an incredibly low energy consumption of 2-3 Watt, through which a contribution to environmental protection and money saving is achieved. The Aoyue 929 is additionally equipped with a lamp cover, which protects the lamp against damage and dirt.

The indispensable tool for lab and every workshop. It is a cold light magnifier produced by AOYUE. This model 929 distinguishes itself by colourfast light, whereby no irritations can occur. The lamp is best suitable for the deciphering of small components on the board or for soldering without additional aids. The lamp can be used for checking if the joints on the board have flaws, which is not possible with the normal eye. It has an incredibly low energy consumption of 25 Watt, through which a contribution to environmental protection and money saving is achieved. The Aoyue 929 is additionally equipped with a lamp cover, which protects the lamp against damage and dirt.

The 932 model is characterised by its continuous and high suction power and its high vacuum volume. Chips weighing 3–40 g can be lifted with this device without any problems. The device is ideally suitable for lifting components off the circuit board when unsoldering. The vacuum pen is made of aluminum, ergonomically shaped, and has an opening that you simply close with your finger as long as you want to keep the component lifted. If the component is to be lowered, simply let go of the opening. This station is indispensable for chip tuning, circuit board repairs, and cell phone repairs.The station comes with a transport lock (red Phillips screw that secures the pump during transport), which must be removed BEFORE switching it on for the first time! The system is then completely ready for use.

This kit Set comprises all you need in order to upgrade the Aoyue stations 852a++ (WilTec-Art. 90852A++); 968 (WilTec-Art. 90968); 968A+ (WilTec-Art. 90968A+); 2702A+ (WilTec-Art. 902702); 2703A+ (WilTec-Art. 902703A+) with a practical vacuum pick up kit. The vacuum pickup kit replaces the smoke absorber, that means you can choose between the two usages by simply reconnecting the hose. You will also receive suction caps that allow you to lift/remove chips and components between 3 - 40g from the circuit board when desoldering. You will receive a vacuum pickup kit. The delivery also includes 3 suction, a screw adapter (22 mm inside thread) and a hose (length: 1.20m Ø 5mm)

The cheap solder fume extraction system from Aoyue, the Aoyue 933 Smoke Absorber. The equipment has two washable filter elements which retain floating particles.With all soldering processes harmful fumes and gases are generated because of the employed solder fluxes. The smoke absorber complies with the workplace regulations stipulated in paragraph § 53 of the German law, and helps to prevent illnesses of the respiratory tract !The use of the solder fume extraction system is neccessary, if one takes into account quality aspects, the above mentioned characteristic and the solder flux precipitation on printed circuit boards, which can lead to problems.The fume extraction kann can be turned on by means of switcher. The equipment can be recommended to all those who solder regularly.

The AOYUE 939 vacuum pick-up pen is characterszed by its high suction volume. Chips weighing 3–40 g can be lifted with this device without any problems. This vacuum pen is ideally suitable for lifting components off the circuit board when unsoldering.Replacement rubber grips can be found in our shop.

AOYUE [1125] Hot Air Nozzle QFP 10x10mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1126] Hot Air Nozzle 15.2mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1127] Hot Air Nozzle 19.2mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1128] Hot Air Nozzle QFP. 14x20mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1132] Hot Air Nozzle SOP 5.6x13mm - SMD Rework Station Rework StationHot air nozzles for standard hot air stations and SMD Rework-Stations with 22mm connection widthPlease make sure, that you choose the right size for your component.Round nozzles can be used for many applications. In the case of nozzles that are used for certain components (for example SOP, BGA, PLCC... you have to choose the appropriate nozzle for your component, so that an inappropriate nozzle does not damage your components.Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1133] Hot Air Nozzle SOP 7.2mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1134] Hot Air Nozzle SOP 7.2mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1135] Hot Air Nozzle 18.5mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

AOYUE [1136] Hot Air Nozzle PLCC 20x20mm Rework Station Reconciling also compatibly to Hakko, Xytronic and Gordak devices. Please also see our other spare parts. If you need help with a fault of your Aoyue product, simply contact us. We're here to help YOU!

The adjustable high performance mini soldering station AOYUE 469 is easy to transport and saves space on the work area due to its light and intelligent design.Equipped with a quickly heating PTC ceramic heater, the station is ideal not only for hobby, but also for professional soldering. The soldering tips are removable from the heater so that they can be effortlessly swapped if needed, which results in a great deal of cost efficiency. You do not have to swap the whole unit, only the tips of soldering irons. It is space-saving through its clever design. It allows a simple storage and transportation of the station together with soldering irons if it is needed outdoors.All in all, you get a well-thought-out soldering station which is suitable for all soldering activities. It is space-saving and cost-efficient at the same time.

• very short heating times• large temperature adjustment• Ideal for replacing components and group of componentsThe antistatic design of the Int 936 prevents PCBs and circuits from being damaged due to static charging. The station has an efficient and precise temperature control by means of which the soldering and desoldering process can be carried out with great care and safety. The soldering temperature is reached and maintained very fast due to the ceramic heating element.Wide range of available soldering tips from Aoyue T-Series.

This product leaves the range, as we want to make room for new products. We are happy to advise you if you need an alternative for this station. The spare parts will be available in future. A solid and shapely design:We provide a convenient tool box; this black plastic box disposes of accessories relating to our soldering station AOYUE Int738+ Repairing Station (WilTec Art 90738+)There is a detachable supporting base for a clear storage of sensitive accessories. The practical handle along with the sturdy locking flaps are coloured in yellow.The tool box contains:1 Tweezer AOYUE T005 with a 7-pin connector along with the matching tool1 Vacuum component lifter (WilTec Art. 90198): Vacuum Pick up Set including 3 attachments, 1 screw adapter (22 mm IG) and 1 hose (1,2 m Ø 5 mm), suitable for the soldering station AOYUE Int738+ Repairing Station. This set replaces the solder fume extraction to the effect that a simple reconnection of the hose makes possible to switch between these two options of application.Due to the supplied attachments, it is possible to lift any chips and components with a weight of 3 up to 40g from the circuit board while desoldering.9 Soldering tips:AOYUE T-B Soldering tip for soldering iron R 0.5 mm (WilTec Art. 91202)AOYUE T-1C Soldering tip for soldering iron Ø 1 mm 60° (WilTec Art. 91204)AOYUE T-0.8D Soldering tip for soldering iron Ø0.8x0.6 mm (WilTec Art. 91210)AOYUE T-1.2D Soldering tip for soldering iron Ø 1.2x0.7 mm (WilTec Art. 91214)AOYUE T-1.6D Soldering tip for soldering iron Ø1.6x0.5 mm (WilTec Art. 91216)AOYUE T-2.4D Soldering tip for soldering iron Ø 2.4x0.5 mm (WilTec Art. 91216)AOYUE T-LB Soldering tip for soldering iron R 0.2 mm (WilTec Art. 91218)AOYUE T-0.5C Soldering tip for soldering iron R 0.5 mm/ 45° (WilTec Art. 91236)AOYUE T-0.8C Soldering tip for soldering iron R 0.8mm/ 45° (WilTec Art. 91238)Soldering fluxSponge (WilTec Art. 912600)1 Soldering tip wiper and metal scourer (WilTec Art. 91806): The soldering tin wiper comprises a metal sponge consisting of 85% bonce and 15% steel. There is no need to moisten the cleaning sponge any longer, so you achieve an effective cleaning without the soldering iron cooling down by the moisture. There are a rubber-coated table stand and carrying handle included in the supply. Spare part heating element

The antistatic design of AOYUE INT 8900 avoids damage of PCB and electronic building elements through e.g. static charge. The user panel is clearly arranged and easy to operate and thus enables an easy handling of the rework station and its functions.• controlled by microprocessor and ESD-safe station• temperature display can be switched over from degrees Fahrenheit to Celsius• quick heating with installed overheat protection• installed temperature sensor that helps to stabilise (temperature-) measurements• integrated air flow meter for precise air volume control • digital control and display of hot air temperature and air pressure• configurable sleep-modus for additional device protection and energy saving• installed auto-cooling-process that protects the system and its components from overheating and extends service life.• compatibility with air nozzles of different typesThe station is delivered with a transport safety device (a red capstan screw that protects the pump during transport). This screw must be removed BEFORE switching on for the first time! After that the system is completely usable.

The Aoyue INT 2702 A+ is a CPU controlled rework station. Its digital display shows precisely the tempertaure and the air flow values. The hot air and the soldering iron temperature is accurately controlled by a microprocessor and sensors that reproduce reliably the temperature and air flow values. The Auto Cooling Function; it blows cold air on the heating element when the hot air is switched off until reaching a low temperature in order to extend the life of the heating element. The soldering iron is optimised for lead-free soldering and comes with a smoke absorber. The high power desoldering gun has a filter spring for an easy cleaning.The ideal, digital lead-free hot air station. This station is indispensable for Chiptuning, repairing mobile phones, laptops and game consoles. This is the lead-free SMD Rework Station from AOYUE. The model 2702A+ is easy manageable. Due to the user-friendly design the operations problems are minimised. The housing is equipped with a practical carrying handle in black/silver. The air flow is permanently displayed via the airflow meter (with blue light) on the side. Additionally you will receive 6 different nozzles and among others a vacuum pick-up suction pen (91939).Non-contact soldering for high requirements. The air flow and the temperature can be adjusted in a wide range. The nozzles can be easily replaced so that each component is soldered by using the suitable nozzle, air and temperature setting. Heating elements and nozzles conform to international standard; suitable for the most SMD components, for instance LEDs, SOIC, CHIP, QFP, PLCC and BGA.You can also use the unit for shrink tubing. The desoldering station facilitates cleaning the solder pads and helps you desolder the wired components fast and easy.The station has a practical holder for the hot air gun, desoldering and soldering iron enabling an easy work. The soldering tips can be changed very fast due to the new aoyue technology. This allows the user to simply replace the soldering tip or the heating element WITHOUT tools (only when the device is turned off). You only need the heat resistant PAD (30150J), that is included in the delivery content; Enclose the soldering tip with this Pad and pull it out of the handhold, this way you can remove the heating element including the soldering tip. The advantage is that you can always change the heating element without the need of a second a soldering iron. By means of resistance measurement you can see within seconds if the "old" heating elemnet is still functional or damaged. Another advantage is: if your soldering tip is worn out you can change it at once with the heating element - and this for an incredible price. What does actually LEAD-FREE for you as customer?Since mid-2006 there is no lead permitted in solder tin anymore. The new solder can be processed much better by using solder stations for lead-free solder.The station is delivered with a transportation safety device (a red screw, which secures the pump during transportation), this has to be removed BEFORE using the station for the first time! Thereafter the station is completely ready for use. You only need a couple of minutes to get your station ready to work. The temperature and the air flow is set via keypads.

Non-contact soldering for special requirements.The air volume and the temperature can be set or adjusted in a wide range, the nozzles can be easily replaced so that each component is soldered by using the suitable nozzle, air and temperature setting. Heating elements and nozzles conform to international standard; suitable for the most SMD components, for instanceLEDs, SOIC, CHIP, QFP, PLCC and BGA.The Aoyue Int 2703 A+ is a CPU controlled Rework station. It unites all advantaged and functions of a hot air soldering station, solder station, fume extraction unit and desoldering gun in one unit.The 2703A+ has a Dual Port System that allows the user to employ simultaneously the lead-free soldering iron as well as the desoldering gun. (the smoke absorber cannot be uses simultaneously with the desoldering gun).Additionally the rework station can use the new generation of BGA hot air nozzles that allow a more effective reflow process on account of better air and heat dispersion. With these Multi-Chamber BGA nozzles the rework of large BGAs (CPU, GPUs) can be carried out more efficiently.Another function of the station is the Aoyue Auto Cooling Function, it blows cold air on the heating element when the hot air is switched off until reaching a low temperature in order to extend the life of the heating element.Temperature and airflow can be adjusted independent of each other via the touch buttons (4 for each) in a temperature range that varies from 100°C - 480°C (hot air) respectively 200°C - 480°C (soldering iron).The station is delivered with a transport safety (a red cross screw that secures the pump during transport), this must be removed BEFORE using the station for the first time!The built-in smoke absorber delivers a constant smoke extraction of 600mmHg. Fume extraction is mandatory according to worplace regulation § 53 in Germany in order to avoid respiratory diseases.

• space saving • short heat-up times • big temperature adjustment range • electrostatically safe discharge (ESD SAFE) • built-in temperature sensor ensures a constant temperature • the digital display shows the set temperature as well as the current temperature Antistatic design of AOYUE Int 3210 which prevents the PCB from being damaged and secures the electronic components, for example damage resulting from static charging. The soldering temperature is shown by means of digital display and can be reached very quickly due to the 70W ceramic element. The station has got a very good and precise temperature control which allows a careful and safe soldering and desoldering. Wide range of available soldering tips from Aoyue T-Series.

• Heating control due to built-in LED• Working temperature can be reached quickly due to the ceramic heating element!• Perfectly suitable for desoldering IC´s, LEDs, cables and other components!• Ergonomic shape and optimal weight balance for fatigue-free use• Easy cleaning of the spring filter by means of simple shaking the waste solder tin• Easy to use rotary button for shakefree workingThe AOYUE Int 474A+, the desoldering station as a stand-alone device.The desoldering station , suitable in any laboratory and workshop. This is a high-tec desoldering pump manufactured by AOYUE. The soldering station is designed in a user-friendly way, easy to operate.To this soldering station you will also receive wide-ranging accessories as for example 4 nozzles.The built-in fume extraction provides for a constant suction of 600mmHG. A Fume Extraction is also required according to §53 of the workplace regulations to prevent respiratory diseases.

The AOYUE Int 474A++ is equipped with an efficient diaphragm pump that operates the fume extraction system. This advanced repair system has a high vacuum capacity and a separate temperature regulation for easy desoldering work The motor and heating element are switched in voltage zero crossing in order to prevent damage due to voltage peaks. All components are manufactured from antistatic materials. The AOYUE Int 474A++ is a CPU controlled ESD safe desoldering station, perfectly suitable for working in laboratories and workshops. Dials for an easy and exact regulation of the working temperature and a large digital display allow an easy use and an uncomplicated operation. With this soldering station you can easily desolder IC´s, LEDs, cable and other wired components. This desoldering station offers a variety of advanced features for the digital calibration of the desoldering gun. Both for the soldering iron and for the desoldering gun there is a programmable "Auto-Sleep" timer. The soldering station is delivered with a transport safety (a red cross screw that secures the pump during transport). This must be removed BEFORE using the station for the first time! Thereafter, the soldering station is completely ready for use.

3 in1:• Soldering Iron • Smoke Absorber • Desoldering GunThe Aoyue Int 701A++ is equipped with an efficient diaphragm pump that operates the fume extraction system. This advanced repair system has a high vacuum capacity and a separate temperature regulation for easy desoldering work.The motor and the heating element are switched in voltage zero crossing in order to prevent damage due to voltage peaks. All component parts are manufactured from antistatic materials.The AOYUE Int 701A++is a CPU controlled rework station. It combines all benefits and functions of a hot air soldering station, fume extraction and desoldering gun in just one unit. The Aoyue Int 701A++ has a Dual Port System that allows the user to employ simultaneously the lead-free soldering iron as well as the desoldering gun.This rework station offers different advanced features for the digital calibration of the soldering iron and desoldering gun.For both devices an "Auto-Sleep" Timer can be programmed.The soldering station is delivered with a transport safety (a red cross screw that secures the pump during transport), that must be removed BEFORE using the station for the first time! Thereafter, the soldering station is completely ready for use. The built-in fume extraction provides for a constant smoke extraction of 600mmHg.A Fume extraction is mandatory according to worplace regulation §53 in Germany to avoid respiratory diseases.

The ideal hot air soldering station. The ideal equipment for use in the laboratory and every workshop. It is a high-tech hot air SMD Rework Station from AOYUE. The model 852 is easy to handle so that you have no problems when using the station! The temperature is indicated by a digital display and can be adjusted by using the selector dial. The air flow is accurately indicated by means of an air tube with a metal ball. The black coated housing is equipped with a practical carrying handle. Even a layman can use the station in a few minutes! You will also receive four different nozzles, a lifting device for components (IC-Popper with a spare gripper), so that you can work WITHOUT additional costs! • the digital display shows the accurate set temperature as well as the current temperature • air flow rate is accurately indicated by the AIR FLOW METER • perfectly suitable for repairing QFP, SOP, PLCC and SOJ components • constant temperature for all air flows! • the air flow meter precisely indicates the air flow all time long • wide temperature and air flow adjustment range. • the cold air cools off the heating element after use continuously, increasing the lifetime of the heating element The station is delivered with a transportation safety device (a red screw, which secures the pump during transportation), this has to be removed BEFORE using the station for the first time! ! The station is completely operational after the screw removal.You need only 5 minutes to do that and then you have a completely functional hot air station. You can adjust the temperature and the air flow by means of two rotary knobs "AIR" and "Set Temp ". The station has a holder for the hot air grip, and a soldering iron holder which allow you to work easily. Find out for yourself!

• CPU monitoredt!• the digital display shows the accurate set temperature as well as the current temperature• air flow rate is accurately indicated by the AIR FLOW METER• perfectly suitable for repairing QFP, SOP, PLCC and SOJ components• integrated temperature sensor ensures a constant temperature regardless of which air flow rate was set• unique 15 minute stand-by automatic Sleep Modus. As a result energy is saved, if the station is needed again just touch the handle and the preconfigurated values will be activated again!• Air flow meter precisely indicates the air flow all time long• Wide temperature and air flow adjustment range.• the cold air cools off the heating element after use continuously, increasing the lifetime of the heating elementThe ideal hot air soldering station. The ideal equipment for use in the laboratory and every workshop. It is a high-tech hot air SMD Rework Station from AOYUE. The model 852++ is easy to handle so that you have no problems when using the station! The temperature is indicated by a digital display. The station changes to power sleep mode when the hot air gun is docked on the handle and at the same time cools down the heating element. This leads to low energy costs and a long operating life of the heating element. The temperature and the air can be adjusted by means of a selector dial. The air flow is accurately indicated by means of an air tube with a metal ball. The black coated housing is equipped with a practical carrying handle. You will also receive four different nozzles, a vacuum pen Aoyue 939 (with spare tips), so that you can work WITHOUT additional costs.The station is delivered with a transportation safety device (a red screw, which secures the pump during transportation), this has to be removed BEFORE using the station for the first time! The station is completely operational after the screw removal.The Station has on the side a practical holder for the hot air grip that makes your work easier.

• CPU monitored!• the digital display shows the accurate set temperature as well as the current temperature• air flow rate is accurately indicated by the AIR FLOW METER• perfectly suitable for repairing QFP, SOP, PLCC and SOJ components• integrated temperature sensor ensures a constant temperature regardless of which air flow rate was set• unique 15 minute stand-by automatic Sleep Modus. As a result energy is saved, if the station is needed again just touch the handle and the preconfigurated values will be activated again!• Air flow meter precisely indicates the air flow all time long• wide temperature and air flow adjustment range.• the cold air cools off the heating element after use continuously, increasing the lifetime of the heating elementThe ideal hot air soldering station. The ideal equipment for use in the laboratory and every workshop. It is a high-tech hot air SMD Rework Station from AOYUE. The model 852++ is easy to handle so that you have no problems when using the station! The temperature is indicated by a digital display. The station changes to power sleep mode when the hot air gun is docked on the handle andand at the same time cools down the heating element. This leads to low energy costs and a long operating life of the heating element. The temperature and the air can be adjusted by means of a selector dial.The air flow is accurately indicated by means of an air tube with a metal ball.The black coated housing is equipped with a practical carrying handle. Even a layman can use the station in a few minutes! You will also receive four different nozzles, a vacuum pen Aoyue 939 (with spare tips), so that you can work WITHOUT additional costs.The station is delivered with a transportation safety device (a red screw, which secures the pump during transportation), this has to be removed BEFORE using the station for the first time! ! The station is completely operational after the screw removal.You need only 5 minutes to do that and then you have a completely functional hot air station.The Station has on the side a practical holder for the hot air grip that makes your work easier.

The Aoyue 853A Preheater works with a fast heating element Quartz IR (Infrared) which is easily and continuously adjustable.The gentle and uniform heating prevents the printed circuit board from being distorted, overheated or damaged. A large digital display with its display options allows you to monitor the selected settings. The pre-heating system with a total heat output of 500 Watt and an adjustable temperature range from 80°C to 450°C provides all that is necessary for working on the pc boards or repairing them. Time and temperature settings can be saved and then run as automated programmes due to the user-defined profile. Additionally the preheating system offers three predifined rework-programms (time / temperature control) to suit different applications. Almost all circuit boards can be safely fixed and worked on due to the integrated board holder. This flexible system allows the user to fix triangular and round boards without difficulties.

The Aoyue Preheater 863 works with a fast Quartz IR heating element. The compact heating element reaches fast the set temperature and maintains it permanently. The station has no engine and is therefore noiseless. The Preheater is delivered with the well-known massive aluminium pc-board holders (100347), which help fix the circuit board on the unit and always has the same distance.

The Aoyue Int866 3in1 PCB Hot Air Rework Soldering Station that is equipped with a powerful 60 watt soldering iron for lead-free solder, hot air and a 400 watt Preheater, is the all-round solution for your workshop.The antistatic design prevents the damage of the boards and the electronic components such as by static electricity. Of course, this station also disposes of a cooldown function so that cold air continuously cools the heating element after use. This increases the service life of the heater. The temperature control allows the soldering or unsoldering with the utmost care and security.The station disposes of a practical holder for the hot air handle and the soldering iron, thus enabling a very light and easy to work. The amount of air and the temperature can be adjusted within a wide range. The jets of the station can be easily replaced, so that each component can be soldered with an optimum nozzle, air and temperature setting. Heating elements and nozzles conform to international standards and are suitable for most SMD components, such as LEDs, SOIC, CHIP, QFP, PLCC, BGA suitable.The preheater, Aoyue Int 866, uses a fast heat up Quartz IR (infrared) heating element that is easily adjustable and infinitely variable. The gentle, uniform heating prevents the distortion, overheating and damage of the circuit boards. By a variety of display options, a large digital display allows the perfect control of the selected settings, temperatures and programs.With a total heating performance of up to 400 watts and a steplessly adjustable temperature range from 100 ° C to 480 ° C, this system offers everything you need for extensive work and repairs on a variety of plates, boards and circuit boards. Accurate temperature measurements can be made using an external temperature sensor anytime and anywhere on the component.With the integrated PCB holder almost all kinds of Printed circuit boards can be securely fixed and processed. This flexible system also allows an easy gripping of round or triangular boards without much effort.You get the base station Aoyue 866 for lead-free soldering including the following accessories:- Soldering Iron (B012) with 60 watts and 10 Soldering Tips- Hot air unit with handle (4 nozzles)- Soldering Iron Holder with dry sponge and tin scraper- Aoyue 939 Vacuum Pickup Set (WilTec-type 91939).- Lifting device (IC Popper)- Aoyue Toolkit - CaseSubject to technical changes!Due to further developments illustrations, functioning steps and technical data may differ slightly.

• Heating control due to built-in LED• Working temperature can be reached very fast due to the ceramic heating element!• Perfectly suitable for desoldering ICs, LEDs, cables and other components!• Ergonomic shape and optimal weight distribution for fatigue-free use• Easy cleaning of the spring filter by means of flapping the waste solder tin• Easy to use rotary button for shakefree working Aoyue Int 8800, the ideal desoldering tool now available as a single station.Suitable for every lab or workshop. It is a high-tec desoldering pump produced by AOYUE.The model Int 8800 is easy to operate, even by an amateur and has a black coated housing.You will also receive other nozzles, and further useful accessories (see above) so that you can start working immediately. The station is delivered pre-installed and ready for use! You just have to plug in the power cord: there are no extra costs, everything you need is included.

The Aoyue 883A Preheater works with a fast Quartz IR( infrared) heating element that can be continously adjusted. The pc-board holder (adjustable) suitable for different types of pc-boards is included in the delivery and ensures an easy and safe fixation of the circuit board. Due to the 3 selectable operational modes and the infrared technology the same working conditions can be maintained all the time enabling a constant good result. The large digital display facilitates a good control of the chosen operational mode due to a large number of display options. Safe working with large pc boards is possible due to a large preheater surface as well as an additional tempertaure sensor (two internal, two external sensors, that are freely positioned and can be queried individually). You can additionally set the "heating peaks" starting with certain temperatures values in certain time intervals.

The antistatic design of the 937 Soldering Station prevents PCBs and circuits from being damaged due to static charging. The Aoyue Soldering Station Int 937 is controlled by a microprocessor and has a short heating up time and a large temperature range. The temperature can be adjusted via traditional knob. In the digital Display the actual and the set temperature is shown.The built-in temperature sensor ensures a constant temperature for precision soldering.Wide range of available soldering tips from Aoyue T-Series.

The antistatic design of the AOYUE INT 9378 PRO Series solder station prevents damage of components and circuit that may result from static charge. Due to this feature, the appliance is suitable for those who want to meet certain industrial quality standards as well as for repair workshops and laboratories.The AOYUE INT 9378 PRO Series solder station is a microprocessor-controlled appliance that features a short heat-up period and a wide temperature setting range. The temperature can be easily set with just one button.The built-in temperature sensor in the heater enables a constant temperature for a precise soldering on temperature-sensitive electronic components and semiconductors.It also features:• Multi-tool connectivity (macro tweezers, micro tweezers, micro-pen, fume extractor pen, LED-soldering irons, sculpture pen)• Automatic tool recognition• Microprocessor-controlled ESD-proof solder station• Automatic Sleep- and Wake-up Mode• Digital offset• Completely digital control• Programmable Sleep-Timer• System lock function• Quick access to personalised/favourite settings• More advanced feature sets• Dimensions: 110 x 98 x 155 mm• Soldering irons with ceramic heater• Temperature range 200°C - 480°C• Power consumption 60 W• Output voltage 24 V

Non-contact soldering. The air volume and the temperature can be set or adjusted in a wide range, the nozzles can be easily replaced so that each component is soldered by using the suitable nozzle, air and temperature setting. The heating elements as well as the nozzles comply with the international standard; suitable for the most SMD components, for instance LEDs, SOIC, CHIP, QFP, PLCC and BGA. The antistatic design of the AOYUE Int 968 prevents PCBs and electronic components from being damaged due to static charging. The control panel as well as the whole rework station are easy to manage and therefore ensure an easy handling. The built-in smoke absorber extracts the fume directly from where it is generated. By blowing, the auto-cooling functionprovides for the lowest possible temperature on the heating element before being switched off in order to extend the life of the heating element. Of course, this repairing system can also be used for the shrinking of shrink hoses and is indispensable in the field of chiptuning, repairing mobile phones, laptops and video game consoles. The built-in solder fume extraction provides a constant suction of 150 g (600mm Hg). To prevent respiratory diseases, the extraction of solder fume is required according to § 53 of the workplace regulations • High heating capacity • SMD fine soldering iron • Highest heating-up • Exact options for adjustment • Automatic cooling - and follow up phase • Fan nozzles in compliance with international standard • Suitable for SOIC, CHIP, QFP, PLCC, PSOP, SSOP, BGA etc. The station is delivered with a transport safety (a red cross screw that secures the pump during transport), which has to be removed BEFORE using the station for the very first time! After removing the safety transport the station is ready to be operated.

Non-contact soldering for high requirements. The air volume and the temperature can be set or adjusted in a wide range, the nozzles can be easily replaced so that each component is soldered by using the suitable nozzle, air and temperature setting. The heating elements as well as the nozzles comply with the international standard; suitable for the most SMD components, for instance LEDs, SOIC, CHIP, QFP, PLCC and BGA. The antistatic design as well as the microcontroller of the AOYUE Int 968 A+ prevents PCBs and electronic components from being damaged due to static charging. The control panel as well as the whole rework station are easy to manage and therefore ensure an easy handling. The built-in smoke absorber extracts the fume directly from where it is generated. The temperature of the soldering ironis shown on the digital display and can be easily adjusted by using a rotary knob ensuring a fast and precise temperature setting. The soldering station informs the user via display about possible malfunctions on the sensors or on the heating elements. By blowing, the Auto-cooling functionprovides for the lowest possible temperature on the heating element before being switched off in order to extend the life of the heating element. Of course, this repairing system can also be used for the shrinking of shrink hoses and is indispensable in the field of chiptuning, repairing mobile phones, laptops and video game consoles. • High heating capacity • SMD fine soldering iron • Highest heating-up • Exact options for adjustment • Automatic cooling - and follow up phase • Fan nozzles in compliance with international standard • Suitable for SOIC, CHIP, QFP, PLCC, PSOP, SSOP, BGA etc. The station is delivered with a transport safety (a red cross screw that secures the pump during transport), which has to be removed BEFORE using the station for the very first time! After removing the safety transport the station is ready to be operated. You don´t need but 5 minutes only to have a complete hot air station The temperature as well as the air flow can be adjusted via "AIR" and "Heater".

Non-contact soldering for high requirements. The air volume and the temperature can be set or adjusted in a wide range, the nozzles can be easily replaced so that each component is soldered by using the suitable nozzle, air and temperature setting. Heating elements and nozzles conform to international standard; suitable for the most SMD components, for instance LEDs, SOIC, CHIP, QFP, PLCC and BGA. This version of the 968a+ is convincing due to its practical accessories. Eight additional soldering tips, a spare heating element, filter pads for the smoke absorber and a tweezer handle for highly specialized work. The antistatic design as well as the microprocessor control of the AOYUE Int 968 A+ multi-function repairing system prevents PCBs and electronic components from being damaged due to static charging. The control panel as well as the whole rework station are easy manageable. The built-in smoke absorber extracts the fume directly at the source where it is generated. The tempertaure of the soldering iron is showed on the digital display and can be adjusted by using the rotary knob allowing a fast and precise temperature setting. The station informs the user via display about possible malfunctions on the sensors or the heating elements. Another function of the station is the Aoyue Auto Cooling Function, it blows cold air on the heating element when the hot air is switched off until reaching a low temperature in order to extend the life of the heating element. The repairing system can also be used for heat shrink-tubing and is indispensable in the filed of chiptuning, repairing mobile phones, laptops and video game consoles • High heating capacity • Exact adjustment possibilities • Automatic cooling and follow up phase • SMD fine soldering iron • Fan nozzles in accordance with international standard • Very fast heating • Suitable for SOIC, CHIP, QFP, PLCC, PSOP, SSOP, BGA etc. The station is delivered with a transport safety (a red cross screw that secures the pump during transport), this must be removed before using the station for the first time! After removing the safety transport the station is fully operational. You only need approx. 5 minutes to have your station ready. The temperature and the air flow can be adjusted via "AIR" and "Heater".

The AOYUE Ritocco 3212A 3D Retouch Pen is made for retouching tin solder as well as plastic materials for 3D printing.Due to a revolutionary compound heater from composite ceramics and an intelligent soldering tip design, the heat-up phase is shorter and the hot swapping of a tip is no more a big deal. The solder tips get easily swapped and you do not have to cool down the heater first. Unlike externally heated soldering irons, a slim Aoyue 3212 Ritocco design reduces heat losses to a minimum so that all the heat is transferred to the soldering tip.Over the display on the upper side of the tip you can adjust various modes for plastic materials. For advanced users there is an “Advanced Mode” which enables to control the temperature externally. The appliance has also a Sleep-Function and turns off automatically if it is not used for some time.Last but not least, the retouch pen stands out with its innovative ergonomic design from other outdated pen designs, which makes it a must-have in 3D printing.